Fudge-Making Mistakes and How to Fix Them (2024)

FAQs

Fudge-Making Mistakes and How to Fix Them? ›

Too little time and the water won't evaporate, causing the fudge to be soft. Conversely, cook it too long and fudge won't contain enough water, making it hard with a dry, crumbly texture. Pay attention to the timetable specified in the recipe, and you'll get the hang of it after a batch or two.

OPTION 3) Sieve together some powdered sugar and cocoa powder, and gradually work this into your unset fudge until it reaches the consistency of dough, then roll out and cut into squares, or shape into balls and then roll in powdered sugar (roll the balls in icing sugar, not yourself).

Good use of failed fudge: fudge that is too hard, too soft, too runny, too sugary, too chewy, etc. Proportions are as follows: for every 2 cups (roughly 1 pound yield) of any failed fudge that is not runny, you'll need 1 egg, ½ cup all-purpose flour, and ½ cup milk. If fudge is soupy, halve the milk (to ¼ cup).

You have to control two temperatures to make successful fudge: the cooking temperature AND the temperature at which the mixture cools before stirring to make it crystallize. Confectionery experiments have shown that the ideal cooking temperature for fudge is around 114 to 115 °C (237 to 239 °F).

To fix oily, hard or grainy fudge, scoop the fudge back into a pot with about a cup of water. Cook it over low heat until the fudge dissolves. Then bring the fudge back up to the temperature specified in the recipe and follow the remaining steps. The flavor may be slightly diluted, but the texture will be improved.

By letting the fudge cool without stirring, you avoid creating seed crystals. Stirring would help sucrose molecules "find" one another and start forming crystals. Stirring also introduces air, dust, and small dried bits from the walls of the saucepan—all potential seeds for crystal formation.

Reset the fudge

This option is to melt back the fudge and to reset it again. This option takes more time and is laborious. Compared to others, it will produce better results. Just as you read earlier you have to mix the ingredients and heat it at 234 degrees.

However, if you don't beat it at all, the crystals won't form properly, so your fudge won't set. If you forget to beat the fudge, try heating it back up over low heat, then beat it once it's slightly softened. If you beat the fudge too soon, the crystals will be too large, and the fudge will be grainy.

Grab the saucepan that you initially used to cook the fudge and toss the fudge back in along with 1 ½ cups of water and a splash of cream. Adding some cream of tartar is a helpful way to keep the sugar crystals at bay as well — it's not essential, but if you have some, definitely pour a little in.

Do you stir fudge while it is boiling? ›

Avoid Stirring Once the Mixture Comes to a Simmer

Another key part of a successful fudge texture is when you stir the mixture. Stirring the sugar and milk during the initial stages of cooking allows the sugar to dissolve. However, once the mixture comes to a boil, it's time to put the spoon down.

Evaporated milk doesn't have sugar added. The sweetened condended milk is needed as no extra sugar is added to the fudge. If evaporated milk were used then the fudge would not be sweet enough and also would still be too soft unless the fudge is frozen.

If there is too much evaporation, when the cooking time is too long, there will not be enough water left in the fudge and it will be too hard.

As strange as it sounds, it is a fact that weather affects fudge making. This is because when the weather is damper with an increased humidity level your Homemade Fudge Recipe will take longer to boil.

To test the boiling mixture for doneness, drop a bit of it into a bowl of cold water. If it forms a ball that is soft enough to flatten between your fingers, the mixture is ready for cooling. When the fudge cools to 110 degrees F/43 degrees C, beat the mixture vigorously with a wooden spoon until it's no longer glossy.

The ingredients for fudge are combined and cooked to 234 degrees, cooled to 110 degrees without stirring, then beaten until creamy. Candy that isn't cooked long enough will end up too soft; overcooking makes fudge crumbly or hard.

To fix soft fudge or hard fudge, simply follow these easy steps: Scrape the fudge back into a large saucepan and add 1 1/2 cups of water. Stir the fudge over low heat until it dissolves. Carefully taste the mixture, as the water probably diluted the flavor.

Reset the fudge

This option is to melt back the fudge and to reset it again. This option takes more time and is laborious. Compared to others, it will produce better results. Just as you read earlier you have to mix the ingredients and heat it at 234 degrees.

We like to set this fudge in the freezer to make it quicker! Once you add the fudge to your pan it will need just 30 minutes in the freezer to set.

Pour Fudge into Prepared Pan

Once the fudge has thickened and the nuts are added, pour the fudge into the prepared pan. Allow it to set at room temperature until firm, about three hours or overnight.